Per Wire in Power Distribution or Collection Mode for (3) three AWG 6 PORTS:

65 Amp 75C Cu per Wire 
75 Amp 90C Cu per Wire 
50 Amp 75C Al per Wire 
60 Amp 90C Al per Wire

Per Wire in Power Distribution or Collection Mode for two (2) AWG 4 PORTS:
85 Amp 75C Cu per wire
95Amp 95C Cu per wire 
65 Amp 75C Al per Wire
75 Amp 90C Al per Wire

Assembly PDF

Dual/Interlocking Lugs

7-9 Wire Application

2S1/0-HEX

and 3S6-2S4-HEX

Assembly PDF

Dual/Interlocking Lugs

6-7 Wire Application

S1/0-HEX

and 3S6-2S4-HEX

Hardware not included.

Lugs sold individually.

For more interlocking lugs

click here.

Dimensions

A: 1.62" (41.1mm)

B: 0.75" (19.1mm)

C: 1.38" (35.1mm)

See Mechanical Drawing for detailed dimensions

"3S6-2S4-HEX" 6 AWG lug, five 5 barrel /wires (3) 6-14AWG plus (2) 4-14AWG wire range, Grounding or Power Distribution or Power Collection Lug. Stacker type, two tier lug. UL Listed for General Use including grounding in dry locations. Up to Five wires (5 conductors) aluminum or copper wire, CU9AL, 90C temperature rating, one (1) 1/4" Bolt mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. Made in the USA from domestic and imported parts. Total current rating with 5 full size copper wires 365 Amp. 

	DIY Mounting Holes™: Cat. No. S6-4 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 3S6-2S4-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make complete contact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Per Wire in Power Distribution or Collection Mode for (3) three AWG 6 PORTS:

65 Amp 75C Cu per Wire 
75 Amp 90C Cu per Wire 
50 Amp 75C Al per Wire 
60 Amp 90C Al per Wire

Per Wire in Power Distribution or Collection Mode for two (2) AWG 4 PORTS:
85 Amp 75C Cu per wire
95Amp 95C Cu per wire 
65 Amp 75C Al per Wire
75 Amp 90C Al per Wire

Assembly PDF

Dual/Interlocking Lugs

7-9 Wire Application

2S1/0-HEX-M

and 3S6-2S4-HEX-M

Assembly PDF

Dual/Interlocking Lugs

6-7 Wire Application

S1/0-HEX-M

and 3S6-2S4-HEX-M

Hardware not included.

Lugs sold individually.

For more interlocking lugs

click here.

Dimensions

A: 1.62" (41.1mm)

B: 0.75" (19.1mm)

C: 1.38" (35.1mm)

See Mechanical Drawing for detailed dimensions

Note!!!   This part has a 3mm hex socket for use in metric countries.  

"3S6-2S4-HEX-M" 6 AWG metric lug, five 5 barrel /wires (3) 6-14AWG plus (2) 4-14AWG wire range, Grounding or Power Distribution or Power Collection Lug. Stacker type, two tier lug. UL Listed for General Use including grounding in dry locations. Up to Five wires (5 conductors) aluminum or copper wire, CU9AL, 90C temperature rating, one (1) 1/4" Bolt mounting hole , Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. Made in the USA from domestic and imported parts. Total current rating with 5 full size copper wires 365 Amp. 5 Metric (3mm) Hex socket screws.

	DIY Mounting Holes™: Cat. No. S6-4 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 3S6-2S4-HEX-M Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make complete contact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

AWG 4, 24Ports:

Per Wire in Power Distribution or Collection Mode:

85 Amp 75C Cu wire
65 Amp 75C Al Wire

Dimensions

A: 2.31" (58.7mm)

B: 1.63" (41.4mm)

C: 2.87" (72.9mm)

L: 1.16" (29.5mm)

See Mechanical Drawing for detailed dimensions

24S4-3, 4 AWG Multi-wire hole, Lug Body Only (24) twenty four 4-14 wire holes lug for power distribution, power collection, structure grounding, floating ground or neutral bar applications. Stacker type, two tier lug. Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application,UL486 ZMVV Listed, UL508A SA1.1 Listed category, and CSA Certified.(2) two mounting bolt holes with clearance for ¼” bolts and threaded for 5/16 UNC bolts. May be bus mounted, bare panel case, or bare chassis mounted or insulated using optional UL508A List SA1.1 category QEUY2 Recognized standoffs for power voltages up to 2000V and floating ground applications when used in accordance with UL508A and NEC code requirements. Copper and tin plated aluminum high strength alloy. Zinc plated steel slotted screws. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. Made in the USA from domestic and imported parts.

UL508A Information on Standoff Insulators

Assembly of Stacked Connectors and Standoffs

	DIY Mounting Holes™: Cat. No. S4-3 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 24S4-3 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

AWG 4, 36Ports:

Per Wire in Power Distribution or Collection Mode:

85 Amp 75C Cu wire
65 Amp 75C Al Wire

Dimensions

A: 2.31" (58.7mm)

B: 1.63" (41.4mm)

C: 4.23" (107.4mm)

See Mechanical Drawing for detailed dimensions

36S4-3, 4 AWG Multi-wire hole LUG BODY ONLY (36) thirty six 4-14 wire holes lug for power distribution, power collection, structure grounding, floating ground or neutral bar applications. Stacker type, two tier lug. Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application,UL486 ZMVV Listed, UL508A SA1.1 Listed category, and CSA Certified. (2) two mounting bolt holes with clearance for ¼” bolts and threaded for 5/16 UNC bolts, SOLD SEPARATELY.

May be bus mounted, bare panel case, or bare chassis mounted or insulated using optional UL508A List SA1.1 category QEUY2 Recognized standoffs for power voltages up to 1500V and floating ground applications when used in accordance with UL508A and NEC code requirements.

Copper and tin plated aluminum high strength alloy. Zinc plated steel slotted screws. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. Made in the USA from domestic and imported parts.

UL508A Information on Standoff Insulators

Assembly of Stacked Connectors and Standoffs

	DIY Mounting Holes™: Cat. No. S4-3 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 36S4-3 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

Dimensions

A: 1.00" (25.4mm) Across Flats

A: 1.14" (29.0mm) Across Points

B: 1.00" (25.4mm)

See Mechanical Drawing for detailed dimensions (page 20).

Dimensions

A: 1.75" (44.5mm)

B: 1.75" (44.5mm)

See Mechanical Drawing for detailed dimensions (page 21).

Per Wire in Power Distribution
or Collection Mode:
115 Amp 75C Cu Wire
130 Amp 90C Cu Wire
90 Amp 75C Al Wire
100 Amp 90C Al Wire

115Amps per #2 Copper Wire Power Looping & Distribution. Satellite Dish Network Installations Ground
 Dry locations, not for direct burial.

Assembly PDF

Dual Interlocking Lugs

Four Wire Application

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.16" (29.4mm)

B: 0.56" (14.3mm)

C: 1.00" (25.4mm)

See Mechanical Drawing for detailed dimensions

"2S2" 2 AWG double wire lug, 2-14 AWG wire range and FLEX, 4-12 AWG, 25mm2-4mm2, wire class G-K including mm2 class 5, 2 barrel, aluminum or copper wire, CU9AL, 90C temperature rating, single 5/16" (8mm) dia. bolt mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

UL & CSA Approved for FLEX wire Class G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

Screwdriver Bit Information

	DIY Mounting Holes™: Cat. No. S2 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S2 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

**TORK KRIMP® Method for clamping wires using uncrimped ferrules is protected under Patent No. 10630005. Full instructions for self crimping ferrules here.

Per Wire in Power Distribution
or Collection Mode:
115 Amp 75C Cu Wire
130 Amp 90C Cu Wire
90 Amp 75C Al Wire
100 Amp 90C Al Wire

115Amps per #2 Copper Wire Power Looping & Distribution. Satellite Dish Network Installations Ground
 Dry locations, not for direct burial.

Assembly PDF

Dual Interlocking Lugs

Four Wire Application

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.16" (29.4mm)

B: 0.56" (14.3mm)

C: 1.00" (25.4mm)

See Mechanical Drawing for detailed dimensions

"2S2-HEX" 2 AWG double wire lug, 2-14 AWG wire range and FLEX, 4-12 AWG, 25mm2-4mm2, wire class G-K including mm2 class 5,double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, single 5/16" (8mm) dia. bolt mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. Made in the USA from domestic and imported parts.

	DIY Mounting Holes™: Cat. No. S2 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S2-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

**TORK KRIMP® Method for clamping wires using uncrimped ferrules is protected under Patent No. 10630005. Full instructions for self crimping ferrules here.

Per Wire in Power Distribution
or Collection Mode:
115 Amp 75C Cu Wire
130 Amp 90C Cu Wire
90 Amp 75C Al Wire
100 Amp 90C Al Wire

115Amps per #2 Copper Wire Power Looping & Distribution. Satellite Dish Network Installations Ground
 Dry locations, not for direct burial.

Assembly PDF

Dual Interlocking Lugs/ Eight Wire Application

Hardware not included. Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.16" (29.4mm)

B: 0.56" (14.3mm)

C: 2.06" (52.4mm)

L: 1.06" (27.0mm)

See Mechanical Drawing for detailed dimensions

"4S2-HEX" 2 AWG Quadruple wire lug, 2-14 AWG wire range, four barrel, aluminum or copper wire, CU9AL, 90C temperature rating, two 5/16" (8mm) dia. bolt mounting holes, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand.

UL & CSA Approved for FLEX wire Class G-K sizes #4-12 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

	DIY Mounting Holes™: Cat. No. S2 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 4S2-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

**TORK KRIMP® Method for clamping wires using uncrimped ferrules is protected under Patent No. 10630005. Full instructions for self crimping ferrules here.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

**TORK KRIMP® Method for clamping wires using uncrimped ferrules is protected under Patent No. 10630005. Full instructions for self crimping ferrules here.

Per Wire in Power Distribution
or Collection Mode:
115 Amp 75C Cu Wire
130 Amp 90C Cu Wire
90 Amp 75C Al Wire
100 Amp 90C Al Wire

115Amps per #2 Copper Wire Power Looping & Distribution. Satellite Dish Network Installations Ground
 Dry locations, not for direct burial.

Assembly PDF

Dual Interlocking Lugs/ Twelve Wire Application

Hardware not included. Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.16" (29.4mm)

B: 0.56" (14.3mm)

C: 3.13" (79.4mm)

L: 1.06" (27.0mm)

See Mechanical Drawing for detailed dimensions

"6S2-HEX" 2 AWG Quadruple wire lug, 2-14 AWG wire range, six barrel, aluminum or copper wire, CU9AL, 90C temperature rating, three 5/16" (8mm) dia. bolt mounting holes, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand.

UL & CSA Approved for FLEX wire Class G-K sizes #4-12 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

	DIY Mounting Holes™: Cat. No. S2 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 6S2-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

**TORK KRIMP® Method for clamping wires using uncrimped ferrules is protected under Patent No. 10630005. Full instructions for self crimping ferrules here.

Approved for two wire use

Assembly PDF

Dual Interlocking Lugs/

Three Wire Application

2S1/0 and S1/0

Assembly PDF

Dual/Interlocking Lugs

6-7 Wire Application

S1/0 and 3S6-2S4-HEX

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.6mm)

C: 0.63" (15.9mm)

See Mechanical Drawing for detailed dimensions

"S1/0" 1/0 AWG Single wire lug, 1/0-14 AWG wire range, Multiple (dual) wire class B/C and FLEX, AWG 1-8, wire class G-K including mm2 including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one mounting hole, slotted screw, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 1/4" bolt mounting hole. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. "Drop-In" Replacement for Homac A-125 and Panduit LAMA1/0-14-Q. Made in the USA from domestic and imported parts.

UL & CSA Approved for Multiple Wires 2X #14 to 2X #4 and (1X) FLEX wire Class G-K sizes #1-#8 AWG
Use of Ferrules (UL Listed) on wires 1-8 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. S1/0 Style No. 1,5
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S1/0 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make complete contact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Approved for two wire use

Assembly PDF

Dual Interlocking Lugs/

Three Wire Application

2S1/0 and S1/0

Assembly PDF

Dual/Interlocking Lugs

6-7 Wire Application

S1/0-HEX and 3S6-2S4-HEX

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.6mm)

C: 0.63" (15.9mm)

See Mechanical Drawing for detailed dimensions

"S1/0-HEX" 1/0 AWG Single wire lug, 1/0-14 AWG wire range, Multiple (dual) class B/C and FLEX wire, 1-8 AWG, class G-K including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one mounting hole, 3/16" A/F Hex Socket Drive screw, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 1/4" bolt mounting hole. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. Made in the USA from domestic and imported parts.

UL & CSA Approved for Multiple Wires 2X #14 to 2X #4 and (1X) FLEX wire Class G-K sizes #1-#8 AWG
Use of Ferrules (UL Listed) on wires 1-8 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. S1/0 Style No. 1,5
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S1/0-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make complete contact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Approved for two wire use

Assembly PDF

Dual Interlocking Lugs/

Three Wire Application

2S1/0 and S1/0

Assembly PDF

Dual/Interlocking Lugs

6-7 Wire Application

S1/0-HEX-M and 3S6-2S4-HEX-M

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.6mm)

C: 0.63" (15.9mm)

See Mechanical Drawing for detailed dimensions

Note!!!   This part has a 5mm hex socket for use in metric countries.

"S1/0-HEX-M" 1/0 AWG metric Single wire lug, 1/0-14 AWG wire range, Multiple (dual) Class B/C wires, and FLEX wire, 1-8 AWG, class G-K including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one mounting hole, METRIC 5mm Hex Socket screw, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 1/4" or 6mm bolt mounting hole. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. Made in the USA from domestic and imported parts.

UL & CSA Approved for Multiple Wires 2X #14 to 2X #4 and (1X) FLEX wire Class G-K sizes #1-#8 AWG
Use of Ferrules (UL Listed) on wires 1-8 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. S1/0 Style No. 1,5
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S1/0-HEX-M Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make complete contact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Approved for two wire use

Assembly PDF

Dual Interlocking Lugs/ 2-4 Wire Application

Hardware not included.

Lugs sold individually.

For more interlocking lugs

click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.6mm)

C: 0.63" (15.9mm)

See Mechanical Drawing for detailed dimensions

"S1/0-34-41" 1/0 AWG Single wire lug, 1/0-14 AWG wire range, Multiple (dual) wire class B/C and FLEX, AWG 1-8, wire class G-K including mm2 including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one mounting hole, slotted screw, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 5/16" bolt mounting hole. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. IHI Connectors® brand. Made in the USA from domestic and imported parts.

UL & CSA Approved for Multiple Wires 2X #14 to 2X #4 and (1X) FLEX wire Class G-K sizes #1-#8 AWG
Use of Ferrules (UL Listed) on wires 1-8 AWG

	DIY Mounting Holes™: Cat. No. S1/0 Style No. 1,5
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S1/0-34-41 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make complete contact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Per Wire in Power Distribution
or Collection Mode: 
150 Amp 75C Cu Wire
170 Amp 90C Cu Wire
120 Amp 75C Al Wire
135 Amp 90C Al Wire

Four wire application

Assembly PDF

Dual Interlocking Lugs/

Three Wire Application

2S1/0 and S1/0

Assembly PDF

Dual/Interlocking Lugs

7-9 Wire Application

2S1/0 and 3S6-2S4-HEX

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.7mm)

C: 1.13" (28.6mm)

See Mechanical Drawing for detailed dimensions

"2S1/0" 1/0 AWG double wire lug, 1/0-14 AWG wire range, and multiple (dual) wires and FLEX wire, 1-8 AWG, class G-K including mm2 class 5, double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, single 1/4" bolt mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

UL & CSA Approved for Multiple Wires 2X #14 to 2X #4 and (1X) FLEX wire Class G-K sizes #1-#8 AWG
Use of Ferrules (UL Listed) on wires 1-8 AWG

	DIY Mounting Holes™: Cat. No. 2S1/0 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S1/0 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

GUIDE ON FLEX

Per Wire in Power Distribution
or Collection Mode:

150 Amp 75C Cu Wire
170 Amp 90C Cu Wire
120 Amp 75C Al Wire
135 Amp 90C Al Wire

Approved for up to 4 wires

Assembly PDF

Dual/Interlocking Lugs

7-9 Wire Application

2S1/0-HEX and 3S6-2S4-HEX

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.7mm)

C: 1.13" (28.6mm)

See Mechanical Drawing for detailed dimensions

"2S1/0-HEX" 1/0 AWG double wire lug, 1/0-14 AWG wire range, and multiple (dual) wires and FLEX wire, 1-8 AWG, class G-K including mm2 class 5, double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, single 1/4" bolt mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 3/16" Hex Socket Screw. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

UL & CSA Approved for Multiple Wires 2X #14 to 2X #4 and (1X) FLEX wire Class G-K sizes #1-#8 AWG
Use of Ferrules (UL Listed) on wires 1-8 AWG

	DIY Mounting Holes™: Cat. No. 2S1/0 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S1/0-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

GUIDE ON FLEX

Per Wire in Power Distribution
or Collection Mode:

150 Amp 75C Cu Wire
170 Amp 90C Cu Wire
120 Amp 75C Al Wire
135 Amp 90C Al Wire

Approved for up to 4 wires

Assembly PDF

Dual/Interlocking Lugs

7-9 Wire Application

2S1/0-HEX-M and 3S6-2S4-HEX-M

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.7mm)

C: 1.13" (28.6mm)

See Mechanical Drawing for detailed dimensions

Note!!!   This part has a 5mm hex socket for use in metric countries.  

"2S1/0-HEX-M" 1/0 AWG metric double wire lug, 1/0-14 AWG wire range, and multiple (dual) wires and FLEX wire, 1-8 AWG, class G-K including mm2 class 5, double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, single 1/4" bolt mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 5mm Hex Socket Screw. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

UL & CSA Approved for Multiple Wires 2X #14 to 2X #4 and (1X) FLEX wire Class G-K sizes #1-#8 AWG
Use of Ferrules (UL Listed) on wires 1-8 AWG, Also class 2 & 5 mm2 sizes single and dual per rating label.

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. 2S1/0 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S1/0-HEX-M Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

Assembly PDF

Dual/Interlocking Lugs

Three Wire Application

2S2/0 and S2/0

Hardware not included.

Lugs sold individually.

For more interlocking lugs

click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.6mm)

C: 0.63" (15.9mm)

See Mechanical Drawing for detailed dimensions

"S2/0" 2/0 AWG Single wire lug, 2/0-14 AWG wire range, and FLEX wire, 1/0-14 AWG, class G-K including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one 1/4" mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Shipped with regular slotted screw or TUFF SLOT™ closed slot which guides driver bit for rapid assembly (subject to availability). TUFF SLOT™ is a trademark of IHI Connectors® Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. "Drop-In" Replacement for Homac A-150 and Panduit LAMA2/0-14-Q.

UL & CSA Approved for (1X) FLEX wire Class G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. S2/0 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S2/0 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual/Interlocking Lugs

Three Wire Application

2S2/0 and S2/0

For more interlocking lugs

click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.6mm)

C: 0.63" (15.9mm)

See Mechanical Drawing for detailed dimensions

"S2/0-HEX" 2/0 AWG Single wire lug, 2/0-14 AWG wire range, and FLEX wire, 1/0-14 AWG, class G-K including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one mounting hole, 3/16" A/F Hex Socket Drive screw, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 1/4" bolt mounting hole. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. Made in the USA from domestic and imported parts.

UL & CSA Approved for (1X) FLEX wire Class
G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. S2/0 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S2/0-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual/Interlocking Lugs

Three Wire Application

2S2/0 and S2/0

For more interlocking lugs

click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.6mm)

C: 0.63" (15.9mm)

See Mechanical Drawing for detailed dimensions

Note!!!   This part has a 5mm hex socket for use in metric countries.  

"S2/0-HEX-M" 2/0 AWG metric single wire lug, 2/0-14 AWG wire range, and FLEX wire, 1/0-14 AWG, class G-K including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one mounting hole, METRIC 5mm Hex Socket screw, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 1/4" or 6mm bolt mounting hole. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. Made in the USA from domestic and imported parts.

UL & CSA Approved for (1X) FLEX wire Class
G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. S2/0 Style No. ALL
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S2/0-HEX-M Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

Per Wire in Power Distribution
or Collection Mode:
175 Amp 75C Cu Wire
195 Amp 90C Cu Wire
135 Amp 75C Al Wire
150 Amp 90C Al Wire

Assembly PDF

Dual/Interlocking Lugs

Three Wire Application

2S2/0 and S2/0

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.7mm)

C: 1.20" (30.6mm)

See Mechanical Drawing for detailed dimensions

"2S2/0" 2/0 AWG double wire lug, 2/0-14 AWG wire range, and FLEX wire, 1/0-14 AWG, class G-K including mm2 class 5, double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, single 1/4" bolt mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Shipped with regular slotted screw or TUFF SLOT™ closed slot which guides driver bit for rapid assembly (subject to availability). TUFF SLOT™ is a trademark of IHI Connectors® Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. Made in the USA from domestic and imported parts. "Drop-In" Replacement for Homac AD-150 and Panduit LAM2A2/0-14-6.

UL & CSA Approved for FLEX wire Class G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. 2S2/0 Style No. 3
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S2/0 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual/Interlocking Lugs

Three Wire Application

2S2/0 and S2/0

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.7mm)

C: 1.20" (30.6mm)

See Mechanical Drawing for detailed dimensions

"2S2/0-HEX" 2/0 AWG double wire lug, 2/0-14 AWG wire range, and FLEX wire, 1/0-14 AWG, class G-K including mm2 class 5, double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, single 1/4" bolt mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 3/16" Hex Socket Screw. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

UL & CSA Approved for FLEX wire Class G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. 2S2/0 Style No. 3
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S2/0-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual/Interlocking Lugs

Three Wire Application

2S2/0 and S2/0

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.7mm)

C: 1.20" (30.6mm)

See Mechanical Drawing for detailed dimensions

Note!!!   This part has a 5mm hex socket for use in metric countries.

"2S2/0-HEX-M" 2/0 AWG metric double wire lug, 2/0-14 AWG wire range, and FLEX wire, 1/0-14 AWG, class G-K including mm2 class 5, double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, single 1/4" bolt (6mm) mounting hole, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. 5mm Metric Hex Socket Screw. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

UL & CSA Approved for FLEX wire Class G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. 2S2/0 Style No. 3
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S2/0-HEX-M Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Per Wire in Power Distribution
or Collection Mode:
175 Amp 75C Cu Wire
195 Amp 90C Cu Wire
135 Amp 75C Al Wire
150 Amp 90C Al Wire

Assembly PDF

Dual Interlocking Lugs/

Four Wire Application

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.7mm)

C: 1.20" (30.6mm)

L: 0.64" (16.3mm)

See Mechanical Drawing for detailed dimensions

"2S2/0-31-42"2/0 AWG double wire lug, 2/0-14 AWG wire range, and FLEX wire, 1/0-14 AWG, class G-K including mm2 class 5, double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, TURN PREVENT USING TWO 1/4" bolts (hole is .315 +/-.007) mounting holes, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Shipped with regular slotted screw or TUFF SLOT™ closed slot which guides driver bit for rapid assembly (subject to availability). TUFF SLOT™ is a trademark of IHI Connectors®. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

UL & CSA Approved for FLEX wire Class G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. 2S2/0 Style No. 3
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S2/0-31-42 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual Interlocking Lugs/

Four Wire Application

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.7mm)

C: 1.20" (30.6mm)

L: 0.64" (16.3mm)

See Mechanical Drawing for detailed dimensions

"2S2/0-31-42-HEX" 2/0 AWG double wire lug, 2/0-14 AWG wire range, and FLEX wire, 1/0-14 AWG, class G-K including mm2 class 5, double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, TURN PREVENT USING TWO 1/4" bolts (hole is .315 +/-.007) mounting holes, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

UL & CSA Approved for FLEX wire Class G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. 2S2/0 Style No. 3
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S2/0-31-42-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual Interlocking Lugs/

Four Wire Application

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 1.47" (37.3mm)

B: 0.81" (20.7mm)

C: 1.20" (30.6mm)

L: 0.64" (16.3mm)

See Mechanical Drawing for detailed dimensions

Note!!!   This part has a 5mm hex socket for use in metric countries.

"2S2/0-31-42-HEX-M" 2/0 AWG metric double wire lug, 2/0-14 AWG wire range, and FLEX wire, 1/0-14 AWG, class G-K including mm2 class 5, double barrel, aluminum or copper wire, CU9AL, 90C temperature rating, TURN PREVENT USING TWO 1/4" bolts (hole is .315 +/-.007) mounting holes, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

UL & CSA Approved for FLEX wire Class G-K sizes #1/0-#14 AWG
Use of Ferrules (UL Listed) on wires 1/0-14 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. 2S2/0 Style No. 3
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 2S2/0-31-42-HEX-M Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual interlocking lugs.

Two wire application.

Hardware not included.

Lugs sold individually.

For more interlocking lugs

click here.

Dimensions

A: 2.00" (50.8mm)

B: 1.13" (28.6mm)

C: 1.00" (25.4mm)

See Mechanical Drawing for detailed dimensions

"S350" 350 kcmil single wire lug, 350 kcmil-6 AWG wire range, and FLEX wire, 262 kcmil-4 AWG, class G-K including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one mounting hole of .343 inch dia 5/16" bolt, NEMA mounting holes and spacing; this is not a NEMA tested part, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. "Drop-In" Replacement for Homac A-350 and Panduit LAMA350-38-Q. Made in the USA from domestic and imported parts.

UL & CSA Approved for FLEX wire Class G-K sizes #262 kcmil-#4 AWG
Use of Ferrules (UL Listed) on wires 262 kcmil-4 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. S350 Style No. 1
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S350 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual/Interlocking Lugs

2 Wire Application

S350-41-50 and S350-41-50

Assembly PDF

Dual Interlocking Lugs/

90 Degree Wire Splicer -

Right angle lug set

Hardware not included.

Lugs sold individually.

For more interlocking lugs

click here.

Dimensions

A: 2.00" (50.8mm)

B: 1.13" (28.6mm)

C: 1.00" (25.4mm)

See Mechanical Drawing

for detailed dimensions

"S350-41-50" 350 kcmil single wire lug, 350 kcmil-6 AWG wire range, and FLEX wire, 262 kcmil-4 AWG, class G-K including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one mounting hole of .50 inch dia 1/2" bolt, NEMA mounting holes and spacing; this is not a NEMA tested part, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. Made in the USA from domestic and imported parts.

UL & CSA Approved for FLEX wire Class G-K sizes #262 kcmil-#4 AWG
Use of Ferrules (UL Listed) on wires 262 kcmil-4 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. S350 Style No. 1
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S350-41-50 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual/Interlocking Lugs

2 Wire Application

S350-53-50 and S350-53-50

Hardware not included.

Lugs sold individually.

For more interlocking lugs

click here.

Dimensions

A: 2.00" (50.8mm)

B: 1.13" (28.6mm)

C: 1.00" (25.4mm)

See Mechanical Drawing for detailed dimensions

"S350-53-50" 350 kcmil Single wire lug, 6 - 350 kcmil AWG wire range, and FLEX wire, 262 kcmil-4 AWG, class G-K including mm2 class 5, single barrel, aluminum or copper wire, CU9AL, 90C temperature rating, one mounting hole of .53 inch dia 1/2" bolt, NEMA mounting holes and spacing; this is not a NEMA tested part, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, CSA Certified. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. International Hydraulics Inc.® brand. Made in the USA from domestic and imported parts.

UL & CSA Approved for FLEX wire Class G-K sizes #262 kcmil-#4 AWG
Use of Ferrules (UL Listed) on wires 262 kcmil-4 AWG

GUIDE ON FLEX

	DIY Mounting Holes™: Cat. No. S350 Style No. 1
CSA and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the S350-53-50 Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual/Interlocking Lugs Eight Wire Application

Hardware not included.

Lugs sold individually.

For more interlocking lugs click here.

Dimensions

A: 2.88" (73.2mm)

B: 1.25" (31.8mm)

C: 3.98" (101.1mm)

L: 1.75" (44.5mm)

See Mechanical Drawing for detailed dimensions

"4S350-56-88" 350 kcmil Quadruple wire panelboard lug, 350kcmil-6 wire range, and FLEX wire, 262 kcmil-4 AWG, class G-K including mm2 class 5, panel Lug. Four barrel / wires (4 conductors) aluminum or copper wire, CU9AL, 90C temperature rating, two 1/2" bolt mounts at 1 3/4" or at 2" centers, NEMA mounting holes and spacing; this is not a NEMA tested part, UL Listed, CSA Certified. International Hydraulics Inc.® brand. Made in the USA from domestic and imported parts. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.

	DIY Mounting Holes™: Cat. No. 2S350 Style No. ALL
Canada and UL permitted field modification by customer per the Drill your own™ Guide for Field Drilling Mounting Holes and the 4S350-56-88-HEX Print

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

Comparison between Panelboard and Switchgear

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make completecontact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Catalog No. "2S350"

E129884 UL486A,B, ZMVV,1243943

CSA 22.2 No.65

Assembly PDF

Dual/Interlocking Lugs

4 Wire Application

Hardware not included.

Lugs sold individually.

For more interlocking lugs

click here.

Dimensions

A: 3.59" (91.2mm)

B: 2.00" (50.8mm)

C: 1.90" (48.3mm)

See Mechanical Drawing for detailed dimensions

"2LS500-41-75" 500 kcmil Double wire lug, 500 kcmil-4/0 AWG wire range, double barrel, aluminum or copper wire, hex socket screws, CU9AL, 90C temperature rating, single 3/8" bolt mounting hole. Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application. Canada Certified. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly.Made in the USA from domestic and imported parts. Interntional Hydraulics Inc. brand.

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make complete contact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual/Interlocking Lugs

4-6 Wire Application

2S250

and 2LS500-TP-41-59

Hardware not included.

Lugs sold individually.

For more interlocking lugs

click here.

Dimensions

A: 3.59" (91.2mm)

B: 2.00" (50.8mm)

C: 1.90" (48.3mm)

See Mechanical Drawing for detailed dimensions

"2LS500-TP-41-59" 500 kcmil Double wire lug, 500 kcmil-4/0 AWG wire range, double barrel, aluminum or copper wire, hex socket screws, CU9AL, 90C temperature rating, single 3/8" bolt mounting hole. Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application. CSA Certified. Stacking, nesting, and interlocking lugs permitted under UL White book ZMVV. Current and temperature rating subject to the lowest temperature rated conducting part in the assembly. Made in the USA from domestic and imported parts. Interntional Hydraulics Inc. brand.

*ZMVV 486 UL Listed Pressure Connector in Specific Dry Location Panel Grounding Applications *NOT a UL467 KDER Grounding Lug *Click here for information for use in UL 508A, UL508 panels and other permitted Grounding Applications subject to further UL investigation.

WIRE CONNECTORS AND SOLDERING LUGS (ZMVV)

INSTALLATION

Wire connectors are intended for use in installations covered by ANSI/NFPA 70, ‘‘National Electrical Code’’ (NEC), and should be installed using the prescribed manufacturer’s installation instructions.

"Stacking of connectors (multiple connectors assembled using a single bolt, nut and washers) may be permitted where mechanical interference is reduced or eliminated with the use of offset tangs, stacking adapters, and the like. The surface contact area of the mounting tang should make complete contact with the mounting surface or the previously stacked connector tang."

Ref. UL White Book ZMVV section

ZMVV UL Whitebook Installation Information

Assembly PDF

Dual Interlocking Lugs/ Two Wire Application

Assembly PDF

Dual Interlocking Lugs/ 90 Degree Wire Splicer - Right angle lug set

Dimensions

A: 2.84" (72.1mm)

B: 1.81" (46.0mm)

C: 1.36" (34.5mm)

See Mechanical Drawing for detailed dimensions